have slowly been restoring a modified windsurfer one design I got about 6 or so months back to like new condition. or as new as possible condition.
so far, I've replaced the mast track with a genuine one,
taken a knife to any jagged bits along the rails,
sanded the hull and rails with wet and dry,
glued and set the flaps and added mylar tape along the length,
sprayed he flaps with silicon pray
sanded back the centreboard.
board came with a new fin.
I recently picked up a second hand sail in very good condition and have tidied up the mast with new plugs so the entire setup is working like new.
only thing left to do is to remove the rust stains off the deck.
any ideas. I was thinking bleach? I've read ajax, gumption, clr.
wondering what people have used.
can confirm that gumption is not going to work.
I've been sailing it since I got it. 
review time.
windsurfer one design. - the orginal.
Try Septone Drifter Hull and stain Remover. You will need an acid to get rid of the rust stains. And like the above product it shouldn't harm the plastic.
Select to expand quotestroppo said..
Try Ranex rust buster it should not effect the plastic !
+1 Stroppo's and PKenny's' comments.
Ranex is good...it's a phosphoric acid.
Septone make one too....it's got some oxalic acid as well as the phosphoric.
Worked a treat on my boat to remove rust stains around the stanchion bases and won't touch plastic.
Old toothbrush to work it into the deck..leave it a few minutes and repeat ..I've just been doing it on my epoxy board!!! Looking good so far.
If you use toothbrush, watch your eyes!
thanks guys,
will swing by bunnings today and see if they have rainex. it's listed on their website so fingers crossed.
if not i'll be at whitworths this week and they've got the septone products..
Select to expand quoteWazzaYotty said..stroppo said..
Try Ranex rust buster it should not effect the plastic !
+1 Stroppo's and PKenny's' comments.
Ranex is good...it's a phosphoric acid.
Septone make one too....it's got some oxalic acid as well as the phosphoric.
Worked a treat on my boat to remove rust stains around the stanchion bases and won't touch plastic.
Old toothbrush to work it into the deck..leave it a few minutes and repeat ..I've just been doing it on my epoxy board!!! Looking good so far.
If you use toothbrush, watch your eyes!
Also good for getting the coffee stains off your teeth.
I gave the ranex a go and it removed a lot of the rust but left a lot behind as well. I then scrubbed the deck with sugar soap as well. it is looking shiny and white now but I need to hit the rust more.
will try the septone next.
Select to expand quoteGestalt said..
I gave the rainex a go and it removed a lot of the rust but left a lot behind as well. I then scrubbed the deck with sugar soap as well. it is looking shiny and white now but I need to hit the rust more.
will try the septone next.
I think Stroppo said 'Ranex', not 'Rainex', in case you bought the wrong stuff.
typo is on my part. I bought the right stuff.
tried to edit it so future people don't get the wrong information.
Select to expand quoteGestalt said..
thanks guys,
will swing by bunnings today and see if they have rainex. it's listed on their website so fingers crossed.
if not i'll be at whitworths this week and they've got the septone products..
Rainex - slippery goop to make your windscreen like a skating rink/ No good for boards
Ranex - rust converter - yes.
Just in case somebody doesn't read the whole thread
alrighty,
I hooked up with Greg this morning and "borrowed" his pack of septone. seems like good stuff and has cleaned the board but hasn't removed the rust stains. They are beyond modern chemical warfare!
Mind you the board is now so white I need to put on sunnies to admire it.
I'll give the ranex one more go. Will make up a compac and apply that. (spelling?)
After that it's lemon juice time!
will take to the hull with some 1200grit wet and dry to finish that before applying some hullkote.
Select to expand quoteGestalt said..
will take to the hull with some 1200grit wet and dry.....
try a small area first, sanding polyethylene might make it furry...
i'll give the clr, and lemon juice a go.
looking at the board this morning I have certainly removed a lot of the staining with what I've done so far. it is actually starting to look pretty good again.
I gave the ranex one more go. Left it on for 3 or 4 hours this time and the rust is almost gone now.
Hope it goes faster! 
Select to expand quoteGestalt said..
i'll give the clr, and lemon juice a go.
looking at the board this morning I have certainly removed a lot of the staining with what I've done so far. it is actually starting to look pretty good again.
You'd better get squeezing buddy ready for the WOD Nationals at RQ 27-29 November 2015. They will be run together with the Raceboards Nationals.
thought I might mozy on down to this one.
guess I better start sailing in deep water and get used to running dead downwind in swell.
). You would have better heat control over the softening/melting of the polymer. Obviously, test on a less visible area first. If you did get any furring from sanding, waving the heat gun over the furry bits tidies them up. Just like a waxless Brazilian.
CLR, my 2 cents worth, that stuff is useless, they should be sued for misleading advertising. On par with the pictured/advertised burgers the fast food chains sell. Recently posted here on a cleaning agent for general grime marks and found the
'Gumption' ants pants.
Select to expand quoteda vecta said..Gestalt said..
i'll give the clr, and lemon juice a go.
looking at the board this morning I have certainly removed a lot of the staining with what I've done so far. it is actually starting to look pretty good again.
You'd better get squeezing buddy ready for the WOD Nationals at RQ 27-29 November 2015. They will be run together with the Raceboards Nationals.
Is this official
Select to expand quoteIBM said..da vecta said..
You'd better get squeezing buddy ready for the WOD Nationals at RQ 27-29 November 2015. They will be run together with the Raceboards Nationals. Is this official
+ 1 ?
go to bcf or bias boating and get some fiberglass hull cleaner make sure you mix with water in strong mixture apply it several times and leave it for 5 minutes each time this will remove rust stains
