Forums > Windsurfing General

tail recess nose&tail rocker

Reply
Created by keef > 9 months ago, 25 Aug 2008
keef
NSW, 2016 posts
25 Aug 2008 9:32PM
Thumbs Up

just finished a slalom board thanks to many guys especially decrepit and Mr. No-one
if you need any help building a board these guys know there there stuff


nobody
NSW, 437 posts
25 Aug 2008 9:50PM
Thumbs Up

Sorry, but I think you have me confused with someone else. You might want to recheck whatever thread you had before. I'm pretty sure I had nothing to do with any board building advice. Interesting looking board though.

keef
NSW, 2016 posts
25 Aug 2008 9:54PM
Thumbs Up

there was a Mr. No-one
on this site who done a wave board and there was a thread on hotwireing if it wasn't you i'm sorry

nobody
NSW, 437 posts
25 Aug 2008 9:58PM
Thumbs Up

No problem. Just didn't want to take credit for someone else. That Mr No-one should change his name. Too much confusion around here.

keef
NSW, 2016 posts
25 Aug 2008 10:00PM
Thumbs Up

sorry attention span isn't to good these days

decrepit
WA, 12770 posts
25 Aug 2008 8:23PM
Thumbs Up

keef said...

sorry attention span isn't to good these days



Can't be too bad, that's a nice looking board.
How's the weight???

keef
NSW, 2016 posts
25 Aug 2008 10:28PM
Thumbs Up

5.3 with deck&pads no straps

keef
NSW, 2016 posts
25 Aug 2008 10:31PM
Thumbs Up

hey decrepit thanks for your help buddy

Bondalucci
VIC, 1579 posts
25 Aug 2008 11:10PM
Thumbs Up

You must have a great Missus,
- allowing you to build your board inside, on the cofee table, over the carpet and all.

I get booted into the garage for my projects !

keef
NSW, 2016 posts
25 Aug 2008 11:19PM
Thumbs Up

missus wots that someone thats ask's too many questions and wants to go and see the inlaws when the winds 30+
not me buddy id rather get my own breakfast

sailpilot
QLD, 785 posts
26 Aug 2008 3:49PM
Thumbs Up

Nice job keef, whats the finish coat you used? and sort of box did you install?
Cheers

keef
NSW, 2016 posts
26 Aug 2008 6:32PM
Thumbs Up

i used fgi RO45 as a skin and to seal the filler coat, its as tough as and hard to sand , the paint was 2 pack northane marine grade,the box is a tuttle

bubs
SA, 924 posts
26 Aug 2008 10:32PM
Thumbs Up

Just curious, how much did it cost to build your own board like that? What tools, equipment, etc. did you have to get your hands on? Brand new boards are so expensive these days, did you save anything by making your own? Or did you do it purely to end up with a better product?

Cheers
Bubs

keef
NSW, 2016 posts
26 Aug 2008 11:55PM
Thumbs Up

the board cost about $800 that's with a block of foam 600x600x2500 i think, and carbon,resin, microballons , ect left over for another board , thats if i make another one
i dont think you make a board to get a better board , you make a board to suit the way and the conditions you sail, what im hopeing to achieve is to have a lower volume board and a smaller sail and plain as early as a board with bigger volume and sail
you see i sail in very flat conditions and im sure the manurfacturas dont make boards just for those conditions , im hopeing to be planeing(off the fin) with a n.p 5/8 slalom
in 15nts, ill let you know on sunday it looks good for saturdays maiden voyage



Subscribe
Reply

Forums > Windsurfing General


"tail recess nose&tail rocker" started by keef